What does a liquid line receiver do?

This website requires certain cookies to work and uses other cookies to help you have the best experience. By visiting this website, certain cookies have already been set, which you may delete and block. By closing this message or continuing to use our site, you agree to the use of cookies. Visit our updated privacy and cookie policy to learn more.

Temprite adds to its line of liquid receiver products with new Horizontal Liquid Receivers for small to large-refrigerant systems. A liquid receiver is a storage tank for holding liquid refrigerant and is located after the condenser in a refrigeration system. It is an important part of any system because it ensures liquid refrigerant is entering the expansion device. Each receiver has inlet and outlet connections and a threaded port for installation of an over-pressure safety-relief device.

Temprite Liquid Receivers accommodate all refrigerants: carbon dioxide (CO2); hydrocarbons (HCs), including ethane, isobutane, and propane, and ammonia (NH3).

The smallest vertical receiver, Model VR6-12, has a bottom mounting stud. Fixed mounting feet are installed on Models VR8-16 through VR18-60. Models VR14-36 through VR18-60 also have lifting lugs in their top domes. All horizontal receivers have adjustable, removable mounting bases. The Model HR12-60 also has lifting lugs.

All receivers are welded and have steel components. Custom liquid receivers and options such as sight glasses and sensors are available on all models.

For more information, contact Temprite.

Get Tech Tips

Subscribe to free tech tips.

Receivers, which we sometimes call “liquid receivers,” are components that store refrigerant. You'll see it on everything from small self-contained refrigeration units to very large commercial and industrial systems.

Many new techs who are used to residential air conditioning confuse receivers with accumulators. It's an understandable error, as they both contain liquid refrigerant. However, you'll find the accumulator on the suction line before the compressor; it prevents liquid from entering the compressor. On the other hand, you'll find a receiver on the liquid line after the condenser. That's because it stores liquid refrigerant that doesn't need to be in circulation for the current heat load.

The liquid receiver stores refrigerant when the system is operating at less than its maximum heat load. In general, systems with receivers are designed so that the receiver can hold the entire system's charge and still be no more than 80% full. That design allows you to pump down the entire system charge into the receiver without the danger of creating hydrostatic pressure; that refers to very high pressures resulting from full liquid expansion. (That's the same reason why we should only fill recovery tanks up to 80% full.)

The multi-position service valve at the outlet of the receiver is called a “King valve.” It can be used for refrigerant circuit access, and it may be fully front seated (turned clockwise) for pump down.

Because a receiver has both liquid and vapor present inside, many techs argue that the refrigerant cannot be “subcooled” in the receiver. The truth is that while the refrigerant that interacts between the liquid and vapor at the top of the receiver is at saturation, the refrigerant below the liquid line can be and usually will and should be subcooled.

—Bryan

Related Tech Tips

“Service factor” is an interesting motor rating that you will see on many motor data tags. It simply means how much additional “work” a motor can do or how much “load” it may be placed under for short periods of time without failure or overload. For example, the FLA or full load amps of the […]

Read more

As an A/C tech, I can sometimes get the terms “defrost termination” and “defrost fail-safe” mixed up because they sound pretty similar. Before we cover these terms, let's set the basic defrost groundwork for refrigeration (coolers and freezers). Defrost is accomplished in one of a few ways; these first two only apply to “coolers” where […]

Read more

Michael Housh from Housh Home Energy in Ohio wrote this tip to help techs determine the air-side charge on a pressure tank. Thanks, Michael! Determining the air-side charge of an expansion tank in a hydronic heating system is a relatively easy task.  A properly sized and charged tank is designed to keep the system pressure […]

Read more

To continue you need to agree to our terms.

The HVAC School site, podcast and daily tech tips Made possible by Generous support from

What is the purpose of a liquid line receiver?

What are the symptoms of a restricted liquid line?

How full should liquid receiver?

What are the two types of liquid receiver?