What type of image will be produced if an object is placed between the focal point and the vertex of a concave mirror?

Next: Image Formation by Convex Up: Paraxial Optics Previous: Spherical Mirrors There are two alternative methods of locating the image formed by a concave mirror. The first is purely graphical, and the second uses simple algebraic analysis.

The graphical method of locating the image produced by a concave mirror consists of drawing light-rays emanating from key points on the object, and finding where these rays are brought to a focus by the mirror. This task can be accomplished using just four simple rules:

An incident ray which is parallel to the principal axis is reflected through the focus
of the mirror.
An incident ray which passes through the focus
of the mirror is reflected parallel to the principal axis.
An incident ray which passes through the centre of curvature
of the mirror is reflected back along its own path (since it is normally incident on the mirror).
An incident ray which strikes the mirror at its vertex
is reflected such that its angle of incidence with respect to the principal axis is equal to its angle of reflection.

The validity of these rules in the paraxial approximation is fairly self-evident.

Consider an object

which is placed a distance

from a concave spherical mirror, as shown in Fig. 71. For the sake of definiteness, let us suppose that the object distance

is greater than the focal length

of the mirror. Each point on the object is assumed to radiate light-rays in all directions. Consider four light-rays emanating from the tip

of the object which strike the mirror, as shown in the figure. The reflected rays are constructed using rules 1-4 above, and the rays are labelled accordingly. It can be seen that the reflected rays all come together at some point

. Thus,

is the image of

(i.e., if we were to place a small projection screen at

then we would see an image of the tip on the screen). As is easily demonstrated, rays emanating from other parts of the object are brought into focus in the vicinity of

such that a complete image of the object is produced between

and

(obviously, point

is the image of point

). This image could be viewed by projecting it onto a screen placed between points

and

. Such an image is termed a real image. Note that the image

would also be directly visible to an observer looking straight at the mirror from a distance greater than the image distance

(since the observer's eyes could not tell that the light-rays diverging from the image were in anyway different from those which would emanate from a real object). According to the figure, the image is inverted with respect to the object, and is also magnified.

Figure 71: Formation of a real image by a concave mirror.

Figure 72 shows what happens when the object distance

is less than the focal length

. In this case, the image appears to an observer looking straight at the mirror to be located behind the mirror. For instance, rays emanating from the tip

of the object appear, after reflection from the mirror, to come from a point

which is behind the mirror. Note that only two rays are used to locate

, for the sake of clarity. In fact, two is the minimum number of rays needed to locate a point image. Of course, the image behind the mirror cannot be viewed by projecting it onto a screen, because there are no real light-rays behind the mirror. This type of image is termed a virtual image. The characteristic difference between a real image and a virtual image is that, immediately after reflection from the mirror, light-rays emitted by the object converge on a real image, but diverge from a virtual image. According to Fig. 72, the image is upright with respect to the object, and is also magnified.

Figure 72: Formation of a virtual image by a concave mirror.

The graphical method described above is fine for developing an intuitive understanding of image formation by concave mirrors, or for checking a calculation, but is a bit too cumbersome for everyday use. The analytic method described below is far more flexible.

Consider an object

placed a distance

in front of a concave mirror of radius of curvature

. In order to find the image

produced by the mirror, we draw two rays from

to the mirror--see Fig. 73. The first, labelled 1, travels from

to the vertex

and is reflected such that its angle of incidence

equals its angle of reflection. The second ray, labelled 2, passes through the centre of curvature

of the mirror, strikes the mirror at point

, and is reflected back along its own path. The two rays meet at point

. Thus,

is the image of

, since point

must lie on the principal axis.

Figure 73: Image formation by a concave mirror.

In the triangle

, we have

, and in the triangle

we have

, where

is the object distance, and

is the image distance. Here,

is the height of the object, and

is the height of the image. By convention,

is a negative number, since the image is inverted (if the image were upright then

would be a positive number). It follows that

(351)

Thus, the magnification

of the image with respect to the object is given by

(352)

By convention,

is negative if the image is inverted with respect to the object, and positive if the image is upright. It is clear that the magnification of the image is just determined by the ratio of the image and object distances from the vertex.

From triangles

and

, we have

and

, respectively. These expressions yield

(353)

Equations (352) and (353) can be combined to give

(354)

which easily reduces to

(355)

This expression relates the object distance, the image distance, and the radius of curvature of the mirror.

For an object which is very far away from the mirror (i.e.,

), so that light-rays from the object are parallel to the principal axis, we expect the image to form at the focal point

of the mirror. Thus, in this case,

, where

is the focal length of the mirror, and Eq. (355) reduces to

(356)

The above expression yields

(357)

In other words, in the paraxial approximation, the focal length of a concave spherical mirror is half of its radius of curvature. Equations (355) and (357) can be combined to give

(358)

The above expression was derived for the case of a real image. However, as is easily demonstrated, it also applies to virtual images provided that the following sign convention is adopted. For real images, which always form in front of the mirror, the image distance

is positive. For virtual images, which always form behind the mirror, the image distance

is negative. It immediately follows, from Eq. (352), that real images are always inverted, and virtual images are always upright. Table 5 shows how the location and character of the image formed in a concave spherical mirror depend on the location of the object, according to Eqs. (352) and (358). It is clear that the modus operandi of a shaving mirror, or a makeup mirror, is to place the object (i.e., a face) between the mirror and the focus of the mirror. The image is upright, (apparently) located behind the mirror, and magnified.

Table 5: Rules for image formation by concave mirrors.

Position of object	Position of image	Character of image
At	At	Real, zero size
Between and	Between and	Real, inverted, diminished
At	At	Real, inverted, same size
Between and	Between and	Real, inverted, magnified
At	At
Between and	From to	Virtual, upright, magnified
At	At	Virtual, upright, same size