You do not need to remove the lead weights inside tires before recycling them. a) true b) false

Q. When does this new law go into effect?
A. This law was signed on September 17, 2010 and as of April 1, 2011 prohibits the use of lead wheel weights to balance tires and by April 1, 2012 no new vehicles may be sold with lead wheel weights.

Q. Are there plans to enforce the law immediately, or is there a grace period?
A. There is no grace period, and the regulated community is expected to be in compliance with the law on April 1, 2011. DEC is providing outreach to the regulated community.

Q. How do I know whether my wheel weight has lead in it?
A. Wheel weights may have a chemical abbreviation written on them. For weights made of steel, you may see the chemical abbreviation "Fe" (for iron, the primary component of steel). The chemical abbreviation "Zn" may be visible on weights made of zinc. Both of these metals tend to be a little lighter in weight than those made of lead, so those weights should be larger than lead weights. You may want to contact the manufacturer if you have questions about the materials in your wheel weights.

Q. Does the law require that I replace lead wheel weights with compliant wheel weights?
A. The law does not require that lead wheel weights be replaced. However, if any work is done on a car's tire(s) that requires an old lead wheel weight to be removed or a lost wheel weight to be replaced, or if a lead wheel weight falls off in the process of working on a tire, the old lead wheel weight cannot be placed back on the tire. Any wheel weight installed on the tire will need to comply with the new law.

Q. If a car with lead wheel weights comes into my repair shop because the tires need to be rebalanced, do I have to install wheel weights made of compliant materials?
A. If you add or replace a wheel weight you have to replace it with a compliant wheel weight.

Q. If a car comes into my repair shop to have a flat tire fixed, and I remove a wheel weight, do I have to replace the wheel weight with one made of a compliant material?
A. If you remove the wheel weight and replace it, you have to replace it with a compliant wheel weight.

Q. What should I do with unwanted stock of lead weights?
A. Options may include returning the wheel weights to your supplier to see if it will exchange them for the type that comply with the new law; sending them for recycling as scrap metal, and disposing of them as a regulated hazardous waste. You cannot discard them in the trash.

Q. Can lead wheel weights be sent back to the supplier or manufacturer and replaced with compliant weights?
A. The law does not require distributors, suppliers, or manufacturers to exchange lead wheel weights with compliant wheel weights, but you can contact your distributor or manufacturer for more information about what to do with your noncompliant lead wheel weights.

Q. Can I sell a new motor vehicle with lead wheel weights?
A. After April 1, 2012, a new motor vehicle cannot be sold with wheel weights containing lead.

Q. Can I sell a used motor vehicle with lead wheel weights?
A. Yes. However, if lead wheel weights are removed from a tire for any reason prior to sale, the old lead wheel weight cannot be placed back on the tire. A wheel weight that complies with the new law will need to be installed on the car.

Q. What penalty provisions apply to a person that improperly stores or releases lead in lead wheel weights to the environment?
A. The penalties in Environmental Conservation Law section 71-3703 would apply. This section provides that any person who violates any of the provisions of, or who fails to perform any duty imposed by section 37-0107 or any rule or regulation promulgated pursuant hereto, shall be liable for a civil penalty not to exceed two thousand five hundred dollars for each such violation and an additional penalty of not more than five hundred dollars for each day during which such violation continues, and, in addition thereto, such person may be enjoined from continuing such violation.

ECL§ 37-0107 prohibits anyone from storing or releasing to the environment substances hazardous or acutely hazardous to public health, safety or the environment in contravention of rules and regulations.

Q. What should I do with lead weights that have been removed from a tire for balancing or repair?
A. Lead wheel weights should be recycled; recycling facilities can be found in the yellow pages.

Upgrade to remove ads

Only A$47.99/year

  • Flashcards

  • Learn

  • Test

  • Match

  • Flashcards

  • Learn

  • Test

  • Match

Terms in this set (100)

Approximately 70% of the world's electronic waste (ewaste) ends up

a. in landfills
b. recycled
c. shipped to India
d. shipped to China
e. incinerated

d. shipped to China

Critics of recycling are most likely to claim

a. It isn't worth the effort.
b. There is no solid-waste problem.
c. Incineration is the safest and most efficient way to dispose of solid wastes.
d. It does make sense to recycle if it costs more than landfilling or incinerating.
e. There is abundant landfill space in all areas.

d. It does make sense to recycle if it costs more than landfilling or incinerating.

The United States produces one-half of the world's ewaste and recycles

a. none of it
b. all of it
c. one-half of it
d. 25% of it
e. 10—15% of it

e. 10—15% of it

Which of the following is not a type of ewaste?

a. discarded TV sets
b. discarded computer printer paper
c. discarded cell pones
d. discarded e-toys
e. discarded computer monitors

b. discarded computer printer paper

Waste that includes paper, food wastes, cans, bottles, yard waste, glass, wood, and similar items is called
a. industrial solid waste
b. hazardous waste
c. municipal solid waste
d. toxic solid waste
e. ewaste

c. municipal solid waste

Hazardous waste includes radioactive wastes, which will have to be stored safely for as long as

a. 15,000 years
b. 50,000 years
c. 100,000 years
d. 240,000 years
e. 1,000,000 years

d. 240,000 years

How much of the waste we mix, crush, and bury could actually be recycled?

a. 33%
b. 50%
c. 67%
d. 75%
e. 90%

d. 75%

With 4.6% of the world's population, the United States produces about _____ of the world's solid waste.
a. one-tenth
b. one-fifth
c. one-forth
d. one-third
e. one-half

d. one-third

For each one pound of electronics in a computer, how much solid and liquid wastes were created?

a. 4 tons
b. 1,000 pounds
c. 500 pounds
d. 250 pounds
e. 10 pounds

a. 4 tons

Garbage produced directly by households and businesses accounts for _____% of the solid waste produced in the United States.

a. less than 2
b. 5
c. 10
d. 15
e. 20

a. less than 2

The amount of solid waste produced in the United States each year would fill a convoy of garbage trucks stretching around the world almost
a. 2 times
b. 4 times
c. 6 times
d. 8 times
e. 10 times

d. 8 times

One way to attempt to deal with the solid wastes we create is to attempt to reduce the environmental impact without trying to reduce the amount of waste produced. This is called

a. waste reduction
b. waste prevention
c. secondary pollution prevention
d. primary pollution prevention
e. waste management

e. waste management

The recycling and composting rate of U.S. municipal solid waste is about

a. 7%
b. 14%
c. 25%
d. 32%
e. 54%

d. 32%

____ percent of the solid waste produced in the United States is buried in landfills.
a. Ninety-eight
b. Fifty-four
c. Forty-eight
d. Thirty-eight
e. Forty

b. Fifty-four

In a low-waste approach, which of the following strategies should be given lowest priority?

a. incinerate
b. reuse
c. reduce
d. bury
e. recycle

d. bury

Taking a refillable coffee cup to the office and using it instead of throwaway cups is an example of __.

a. refuse
b. reduce
c. reuse
d. repurpose
e. recycle

c. reuse

Which of the following is the least desirable from an environmental standpoint?

a. refuse
b. reduce
c. reuse
d. repurpose
e. recycle

e. recycle

Scientists estimate that in a low-waste society _____ of solid and hazardous waste could be eliminated through reduction, reuse, and recycling.

a. 5-10%
b. 15-25%
c. 25-50%
d. 65-80%
e. 75-90%

e. 75-90%

All of the following reflect a low-waste approach, except

a. extending the useful lifetime for a product
b. designing products that pollute less when used
c. built-in obsolescence
d. modular construction for repair
e. eliminating unnecessary packaging

c. built-in obsolescence

Which is the most advanced approach?

a. recycling materials
b. using biodegradable material
c. creating more durable products
d. reducing the amount of materials used
e. reusing materials

d. reducing the amount of materials used

As a form of waste reduction, reuse does all of the following, except:

a. decreases the use of matter resources
b. decreases the use of energy resources
c. cuts pollution and waste
d. creates local jobs
e. costs money

e. costs money

Studies by two soft-drink companies indicate that 21-oz bottles of soft drinks cost _____ in refillable bottles than throw away bottles.

a. three times more
b. two times more
c. about the same
d. one-third less
e. four times more

d. one-third less

Environmentalists say that the best way to handle soft-drink and beer containers is to

a. use landfills
b. recycle aluminum cans
c. use stainless steel cans
d. use reusable glass bottles
e. bury them

d. use reusable glass bottles

How many U.S. states have bottle laws?

a. 1
b. 6
c. 11
d. 22
e. 50

c. 11

_____ has a beverage-container deposit fee that is 50% higher than the cost of the drink, to encourage use of refillable bottles.

a. Italy
b. Ecuador
c. Germany
d. Canada
e. United States

b. Ecuador

The most energy-efficient beverage container on the market is

a. refillable glass
b. recyclable aluminum
c. stainless steel
d. recyclable plastic
e. carton

a. refillable glass

At the checkout counter, an environmentalist is most likely to

a. say "Plastic please."
b. say "Paper please."
c. say "I brought my own bag."
d. walk out of the store
e. say "Either plastic or paper."

c. say "I brought my own bag."

Compost is most accurately described as

a. manure
b. landfill byproducts
c. pure garbage
d. soil conditioner and organic fertilizer
e. humus

d. soil conditioner and organic fertilizer

Currently, the United States recycles about _____ of all its wastepaper.

a. 16%
b. 26%
c. 46%
d. 56%
e. 66%

d. 56%

Source separation differs from materials-recovery facilities in all but which of the following?

a. It is cheaper.
b. It yields cleaner and more valuable recyclables.
c. It produces less air and water pollution.
d. It encourages higher throughput of matter.
e. It saves more energy and provides more jobs per unit of material recycled

d. It encourages higher throughput of matter.

Consumers of recycled products are most effective when they maximize the amount of _____ waste in the products.

a. pre-producer
b. post-producer
c. pre-consumer
d. post-consumer
e. producer

d. post-consumer

Partially biodegradable plastics need _____ to be broken down.

a. light
b. oxygen and moisture
c. anaerobic conditions
d. cool conditions
e. heat

d. cool conditions

Which of the following is not true of plastic materials?

a. They decompose readily in landfills.
b. Toxic lead and cadmium can leach out of plastics.
c. They can harm animals that swallow them or become entangled in them.
d. They are made of many different types of resins.
e. They are unnecessarily and excessively used as single-use and throw-away packaging.

a. They decompose readily in landfills.

Of the following materials, the most difficult to recycle is
a. glass
b. plastic
c. paper
d. aluminum
e. cardboard

b. plastic

Plastic is not recycled at a high rate for all of the following reasons, except
a. Separating the many resins used is difficult.
b. Plastics contain stabilizers and other chemicals that must be removed.
c. The amount of plastic resin in each item is small.
d. The price of oil has made it cheaper to use virgin resin.
e. Health concerns exist about continual use of plastic.

e. Health concerns exist about continual use of plastic.

In order for an incinerator to be a safe alternative for waste disposal all of the following must be done, except

a. Find a use for the heat generated.
b. Control release of CO2.
c. Monitor for toxic metals.
d. Monitor and remove toxic fly ash.
e. Dispose of hazardous materials in an approved landfill.

a. Find a use for the heat generated.

Incinerators

a. create many low-paying jobs
b. are inexpensive to build
c. are inexpensive to operate and maintain
d. produce toxic substances in fly ash and bottom ash
e. create few high paying jobs

produce toxic substances in fly ash and bottom ash

Sanitary landfills typically have problems with

a. rodents and insects
b. odor
c. open, uncovered garbage
d. traffic, noise, and dust
e. spread of disease

traffic, noise, and dust

The top priority when dealing with hazardous waste should be

a. making it less toxic
b. making certain it is stored properly
c. pollution prevention and waste reduction
d. making certain it is transported safely
e. protecting groundwater

c. pollution prevention and waste reduction

All of the following are means of detoxifying hazardous and toxic wastes, except

a. phytoremediation
b. crushing and grinding
c. bioremediation
d. nanomagnets
e. chemical methods

b. crushing and grinding

Since 1995, Superfund has been primarily funded by

a. identified polluters
b. taxes on all industries
c. taxes on all industries and fines on identified polluters
d. taxpayers
e. Superfund is no longer a funded program.

d. taxpayers

Which of the following is a disadvantage of using a plasma torch to detoxify hazardous waste?

a. mobility
b. toxic ash production
c. cost
d. production of SO2 gas
e. low energy use

c. cost

Which of the following methods uses natural or genetically engineered plants to absorb, filter, and remove contaminants from soil and water?

a. phytoremediation
b. physical methods
c. bioremediation
d. nanomagnets
e. chemical methods

a. phytoremediation

Which of the following is the most common method of storage of hazardous wastes used in most countries of the world?

a. burial at sea
b. above ground tanks
c. inside plants and warehouses
d. land burial
e. glassification

d. land burial

What percentage of liquid hazardous waste in the U.S. is injected into deep disposal wells?

a. 34%
b. 14%
c. 54%
d. 24%
e. 64%

e. 64%

Of the following methods of reducing hazardous wastes, the most desirable is

a. incineration
b. conversion to less hazardous materials
c. perpetual storage
d. deposit in ocean trenches
e. recycling and reusing hazardous wastes

b. conversion to less hazardous materials

What percentage of the hazardous waste produced in the U.S. is regulated by the Resource Conservation and Recovery Act?

a. 5%
b. 10%
c. 15%
d. 20%
e. 25%

a. 5%

A disproportionate share of polluting factories, hazardous waste dumps, incinerators, and landfills in the U.S. are located in communities populated by all of the following, except

a. African Americans
b. Asian Americans
c. Caucasians
d. Latinos
e. working poor

c. Caucasians

In 1989 an international treaty called the Basel Convention banned developed countries from shipping hazardous waste to developing countries. Which of the following countries has not ratified the treaty?

a. Lithuania
b. Burkina Faso
c. Cuba
d. Democratic Republic of Congo
e. United States

e. United States

Which of the following principles does not contribute to a transition to a low-waste society?

a. Economic growth and free markets reduce waste.
b. Everything is connected.
c. There is no "away."
d. Reduce, reuse, recycle are the best priorities for using matter.
e. Dilution is not always the solution to pollution.

a. Economic growth and free markets reduce waste.

The fastest growing solid waste problem in the U.S. and in the world is ewaste.

True
False

True

The European Union has an approach to ewaste, known as the cradle-to-grave approach, which requires manufacturers to provide health benefits from cradle-to-grave.

True
False

False

About 98.5% of all solid waste in the United States is industrial solid waste.

True
False

...

Since 1990 the annual production of municipal solid waste has doubled.

True
False

false

Trash production, by weight, in the city of New York reached its peak between 1920 and 1940.

True
False

true

Each day the average American produces about 2.0 kilograms (4.5 pounds) of municipal solid waste, three-fourths of which is dumped in landfills.

True
False

True

Most scientists think that waste management should be the last priority for dealing with material use and solid waste.

True
False

True

Integrated Waste Management involves combining several different waste management methods into one single strategy.

True
False

True

Waste reduction is the preferred solution to managing solid wastes because it does not try to avoid the issue of economic growth.

True
False

True

The ecoindustrial revolution includes the redesign of manufacturing processes to mimic how nature reduces and recycles wastes.

True
False

True

Reusing products can be a health hazard for the poor in developing countries who dismantle products to extract usable parts.

True
False

True

Large beverage industries have used their political and financial clout to force most U.S. states to pass bottle bills.

True
False

False

Plastics are routinely recycled because they are composed of pure resins that can be extracted and used for other plastic products.

True
False

False

The products of composting can be used to slow soil erosion, retain water, and improve crop yields.

True
False

True

The incineration of hazardous wastes is quick, conserves space, and reduces waste volume but is not used because of the increased water pollution that results.

True
False

False

At sanitary landfills, consideration of leachate is of most importance as far as environmental preservation is concerned.

True
False

True

The National Priorities List identifies hazardous waste sites, with clean up of these sites based on priority and severity.

True
False

False

The Basal Action Network says that most businesses that call themselves ewaste recyclers take your recycling fee and ship the waste to China, India, or Nigeria.

True
False

True

Burial or long-term storage of hazardous waste is the first priority for environmental scientists.

True
False

False

NOPE calls for drastically reducing production of toxic and hazardous wastes by emphasizing pollution prevention and using the precautionary principle.

True
False

True

No country has yet to institute a ban on persistent organic pollutants.

True
False

False

The best and cheapest ways to deal with solid and hazardous wastes are waste reduction and pollution prevention.

True
False

True

__________ is the fastest-growing solid waste problem in the United States and in the world.

Ewaste

__________ __________ __________ is the combined solid waste produced by homes and workplaces.

Municipal solid waste

The world's largest landfill, called _________ __________, outside of New York City closed in 2001; it is being turned into a park and nature preserve.

Fresh kills

The two largest classes of hazardous wastes are __________ and ___________.

organic compounds; toxic heavy metals

Most analysts call for using __________ __________ __________—a variety of strategies for both waste reduction and waste management.

intergrated waste management

From an environmental standpoint, the first two Rs, __________ and __________, are better alternatives because they are input or prevention approaches.

reduce; reuse

In the __________ __________ manufacturing processes are being redesigned to mimic how nature reduces and recycles wastes.

ecoindustrial evolution

__________-_____-__________ laws require companies to take back various consumer products instead of having them put in landfills or incinerated.

Cradle-to-grave

Tires being shredded and converted into surfacing for public roads is an example of __________

secondary recycling

_________ are inefficient because they are expensive to build, discharge toxic emissions, and can produce a toxic ash.

(MRF) Materials-recovery facilities

__________ occurs when waste is made into new products of the original type.

Primary, or closed-loop, recycling

Ponds, pits, or lagoons into which liners are placed and liquid hazardous wastes are stored are called __________ __________.

surface impoundments

13. __________ systems charge consumers for the amount of garbage picked up but do not charge for the amount of materials separated that can be recycled.

Pay-as-you-throw

__________ are sites where waste is isolated from the environment until it is safe.

Sanitary landfills

__________-_____-__________ incinerators produce 38% less CO2 per unit of energy than coal-burning power plants.

Waste-to-energy

Japan embraces resource exchange, and most of the country's municipal solid waste is sent to __________-_____-__________ _____________ to produce steam.

waste-to-energy incinerators

__________ involves using natural or genetically engineered plants to absorb, filter, and remove contaminants.

Phytoremediation

The U.S. has passed laws to facilitate the cleanup of abandoned, contaminated industrial sites, known as __________.

brownfields

In the United States, the __________ __________ _____ __________ __________ regulates only a small percentage of all hazardous waste.

Resource Conservation and Recovery Act

__________ utilizes bacteria and enzymes instead of plants to filter or destroy hazardous substances.

Bioremediation.

The call to drastically reduce toxic and hazardous waste, at least by 75%, is part of a concept called NOPE, which stands for

Not On Planet Earth

We should mimic nature by reusing, recycling, or composting at least _____% of the solid wastes we produce.

75

Use the Figure above to answer the following questions.

Choose the letter that represents photostabilization.

B

Choose the letter that represents phytoextraction.

d

Choose the letter that represents rhizofiltration.

a

Choose the letter that represents phytodegredation.

c

Use the second chart to answer the following questions.

Why is recycling an output approach for environmental concerns?

Recycling deals with wastes already produced and harmful to the environment. The wastes are the outputs. Prevention of waste production or reduction of wastes is the best approach. Recycling usually reduces pollution and waste production.

Explain how recycling reduces energy demand and makes fuel supplies last longer.

Recycling uses oil products like tires for other applications. Waste generated in manufacturing a product, for example heat, can be used to warm the manufacturer's water, etc.

Sets with similar terms

Chapter 21 Solid and Hazardous Waste

78 terms

jwissink21

APES Ch. 21 Review

94 terms

Halloweencat31

ENVS Chapter 21

50 terms

MacKenzie698

APES Chapter 21

50 terms

Megan_MichtaTEACHER

Sets found in the same folder

Ch. 19 Vocabulary

19 terms

ljcbball

APES Final

29 terms

rachelhollands

Environmental science exam 2

60 terms

alex_saccomondo

APES Chapter 18: Mind tap Post Learning Assesment

15 terms

Madelyn_Gordon

Other sets by this creator

Reinsurance final

8 terms

willcobley

Reinsurance outline

30 terms

willcobley

OB CH7

62 terms

willcobley

Quiz 4 Christianity

14 terms

willcobley

Verified questions

ENVIRONMENTAL SCIENCE

List the six kingdoms of organisms and the characteristics of each kingdom.

Verified answer

ENVIRONMENTAL SCIENCE

Why is the production of electricity from geothermal energy practical only in certain parts of the world?

Verified answer

ENVIRONMENTAL SCIENCE

Which worldview considers ecosystems to have intrinsic value? I. Anthropocentric, II. Biocentric, III. Ecocentric. (a) l only, (b) I and III only, (c) II only, (d) II and III only, (e) III only.

Verified answer

ENVIRONMENTAL SCIENCE

Choose the best answer. Which food chain found on the Serengeti Plain is in the correct sequence from lowest trophic level to highest? (a) shrubs-gazelles-cheetahs-decomposers (b) shrubs-decomposers-cheetahs-gazelles (c) gazelles-decomposers-cheetahs-shrubs (d) decomposers-cheetahs-shrubs-gazelles

Verified answer

Other Quizlet sets

Genetics and Evolution Final Exam

64 terms

allielarsen166PLUS

Study guide 12/13

26 terms

melanienunezp

2nd exam MEDS + ElectroConvulsive Therapy (ECT)

13 terms

navia21

Related questions

QUESTION

dumping large amounts of nitrogen and phosphorus promote rapid growth and algae often resulting in an "algal bloom". This process is known as

3 answers

QUESTION

What are the sources of air that circulate in the Midwest?

8 answers

QUESTION

As water cools, it contracts in volume until it reaches 4° C (39° F), at which point it begins to expand as it continues to cool.

5 answers

QUESTION

What practice is consistent with the production of organic crops according to the United States Department of Agriculture

2 answers

Do you need to remove the lead weights in tires before recycling them?

A. Yes. However, if lead wheel weights are removed from a tire for any reason prior to sale, the old lead wheel weight cannot be placed back on the tire. A wheel weight that complies with the new law will need to be installed on the car.

Do they still use lead weights to balance tires?

Most new cars and light trucks sold in the US feature zinc or steel wheel weights, and all new cars and light trucks sold in the US have been free of lead wheel weights since 2009. Vehicle manufacturers made a significant commitment to phase out this use of lead.

What can you do with old wheel weights?

Ask your wheel weight supplier if they have a program for recycling the old wheel weights. 2. You may also check with your automotive battery supplier or a local scrap metal recycler. Recycle used lead wheel weights in an environmentally responsible manner.

What are lead wheel weights?

Lead wheel weights are defined by the new law, California Health and Safety Code Sections 25215.6-25215.7, as any weights containing more than 0.1 percent lead. The law took effect Jan. 1, 2010, and applies whether a weight is installed on a new vehicle or is removed and reinstalled during wheel balancing.